All Tutorials will be E-mailed immediately after the Payment and can also be Downloaded by clicking on Tutorial Bucket.
Shopping Cart
0 item(s) - $0.00
Your shopping cart is empty!
Final Guides

ECET 340

Refine Search

$65.00

This Tutorial has been rated A+ by student like you.

ECET 340 Week 1 HomeWork 1 ECET 340 Week 1 iLab 1 ECET 340 Week 2 HomeWork 2 ECET 340 Week 2 iLab 2 ECET 340 Week 3 HomeWork 3 ECET 340 Week 3 iLab 3 ECET 340 Week 4 HomeWork 4 ECET 340 Week 4 iLab 4 ECET 340 Week 5 HomeWork 5 ECET 340 Week 5 iLab 5 ECET 34..
$13.00

This Tutorial has been rated A by student like you.

1. Give three examples each of internal and external peripheral devices as referenced to the HCS12 microcontroller and not an entire PC. (2 points) 2. Given “the requirements of each signal’s destination must match the capabilities of the signal’s source,” name some of the electrical signal ..
$13.00

This Tutorial has been rated No rating by student like you.

OBJECTIVES: To become familiar with Microcontroller MC9S12 parallel ports and how simple input and output devices are interfaced through them. To learn how to program I/O instructions in C language. To learn how to organize a program to read data from input ports, process the ..
$9.00

This Tutorial has been rated A by student like you.

Laboratory Title: LCDs and Keypad     Objectives:   1. To become familiar with LCD initialization 2. Displaying messages on the LCD 3. Developing a poll routine to capture Keypad information 4. Combine the LCD and Keypad programs    ..
$13.00

This Tutorial has been rated A+ by student like you.

1. Where does program control transfer to when an interrupt occurs? +2 points 2. Which one of the following Interrupts has highest priority? +2 points 3. RAM Vector table addresses $3E52 belongs to which interrupt? +2 points 4. Before exiting an ISR, the programmer should use which co..
$13.00

This Tutorial has been rated A by student like you.

ECET 340 Week 2 iLab 2 ..
$9.00

This Tutorial has been rated No rating by student like you.

Objectives: 1.To become familiar with the configuring and enabling of interrupts 2.Using the external interrupt 3.Using the Real Time Interrupt 4.To combine two interrupts within a program   ..
$13.00

This Tutorial has been rated No rating by student like you.

1. Sketch a circuit that can be used to debounce a pushbutton and explain how it works. (4 points max) 2. In Figure 7.32 on page 339 of the Huang textbook, if the row has and the columnsare , which key is pressed? (2 points max) 3. In Figure 7.32 on page 339 of the Huang textbook, explain..
$13.00

This Tutorial has been rated A+ by student like you.

SOLVED ECET 340 iLAB3 OBJECTIVES: To learn the basic operation of a keypad. To understand how to interface a keypad to a microprocessor. To learn how to program a keypad driver in C language. To learn how to program a keypad activated interrupt that identifies the ke..
$8.99

This Tutorial has been rated No rating by student like you.

Objectives: 1.To become familiar with the configuring and enabling of timers 2.Using the timer counter 3.Using the input capture timer   ..
$13.00

This Tutorial has been rated A by student like you.

1. Determine the conversion time for an ADC0804 (8-bit), where 66 clocks per bit are required, if its clock frequency is 50 kHz. 2. If an 8-bit SAR has Vref = 10 V, what is the binary value for an input voltage of 7.28 V? 3. What is the percent error for the binary answer found in Probl..
$13.00

This Tutorial has been rated No rating by student like you.

I. OBJECTIVES: To learn how to use A-to-D converters to digitize signals from analog input devices. To learn how to write a C language program that samples the data from an analog device, digitizes it and formats it for output on an LCD. To become more proficient in programmin..
$8.99

This Tutorial has been rated A by student like you.

Objectives: 1.Become familiar with the configuring and enabling of the event counter. 2.Use the digital-to-analog converter to produce signals.   ..
$13.00

This Tutorial has been rated A by student like you.

1. Explain, briefly, why an analog restoring filter is sometimes used at the output of a DAC. 2. Given Iref = 2 mA for a DAC1408 IC, find Iout for the input 1110 1110 3. Find the number of discrete voltages output by a 12-bit DAC. Show work. 4. Use the internet to locate the data shee..
$13.00

This Tutorial has been rated A+ by student like you.

Scenario/Summary This week's lab covers two areas, conversion of digital HCS12  signals to an analog format, and the use of a Serial Peripheral Interface (SPI)  to transfer data, and commands between the HCS12, and the DAC  peripheral.  Deliverables For..
$8.99

This Tutorial has been rated No rating by student like you.

Objectives: 1.To become familiar with the configuring and enabling of the analog-to-digital converter 2.Usage of both the ATD and RTI interrupt service routines   ..
$13.00

This Tutorial has been rated A+ by student like you.

1. What are the four main functions of the HC12 Timer unit? 2. Two input capture events occur at counts 0x1037 and 0xFF20 of the free-running counter. How many counts (in decimal) have transpired between these two events? 3. What is the maximum time possible before the free-running coun..
$13.00

This Tutorial has been rated No rating by student like you.

ECET 340 Week 6 iLab 6 ..
$9.00

This Tutorial has been rated A+ by student like you.

Objectives:   1. To become familiar with the configuring and enabling of serial communication transmitter 2. To configure the microcontroller to receive serial communications from another device   1 What commands are utilized for the configuration of the asynchro..
$13.00

This Tutorial has been rated A by student like you.

1. The movable part of the solenoid is the: +2 points 2. Why is the 6N139 optoisolator used in the interfaces to devices such as large motors? +2 points 3. Calculate the number of steps per revolution for a stepper motor with a step angle of 7.5°. +2 points 4. How is stepper motor spe..
$13.00

This Tutorial has been rated No rating by student like you.

ECET 340 Week 7 iLab 7 ..
$8.99

This Tutorial has been rated A by student like you.

Title: HVAC Controller I. OBJECTIVES 1.To become familiar with the thermistor 2.To use integrated modular programming techniques in developing the project 3.To write a report document for the HVAC Controller   ..
Newtonhelp © 2019
Powered By Uophelp